Mar 23, 2017 - OWNER'S MANUAL How to install, operate and maintain your EcoWater Systems Electronic Demand Water Softener EcoWater Systems LLC. Water Softener Troubleshooting & Diagnostic Procedures. I currently have a water softener system in my home BUT, there are always water marks on my.

• EcoWater Systems Conditioner with Remote (ECR) EcoWater Systems Refiner with Remote (ERR) SERIES 3500 & 3502 Systems Tested and Certified by NSF Interna- ERR 3500R20 & ERR 3502R30 are Tested tional and WQA against NSF/ANSI Standard and Certified by WQA against NSF/ANSI 44 for water softening performance and the Standard 42 for chlorine taste and odor. • Consult the dealer or an experienced radio/TV tech- Use care when handling the EcoWater Systems condi- nician for help. Do not turn upside down, drop, or set on Changes or modifications not expressly approved by sharp protrusions. • Your local dealer will provide details regarding this warranty or writing within 30 days from the expiration of these guar- will refer you to the factory for additional information. In addition, the 3500 SERIES antees upon EcoWater Systems LLC, P.O. • OTHER REQUIREMENTS STANDPIPE LAUNDRY TUB A drain is needed for recharge discharge water. A floor drain is preferred, close to the EcoWater Systems con- FIG.

1B ditioner/refiner. A laundry tub, standpipe, etc., are other options (See Figure 1B). NOTE: The Commonwealth of Massachusetts plumbing A 120V, 60 Hz, grounded, continuously “live”. • TUBES cover, bag(s) of small parts needed to assemble and install a. If installing an EcoWater Systems Bypass Valve, put the unit, plus this manual, in the other. Lubricated o-ring seals onto both bypass valve ports (See EcoWater Systems conditioner/refiner models R20, R30 and Figure 3B).

• (See Figure 4A). 3 - - Valve Bypass BYPASS INLET OUTLET VALVE VALVE VALVE nozzle & venturi EcoWater Systems Bypass Valve ground clamp o- -ring from conditioner/ brine to conditioner/ refiner elbow PULL OUT. Cubase crack download. • Fully open two or more conditioned cold water faucets nearby the EcoWater Systems conditioner/refiner. Care is taken at the factory to keep your EcoWater Systems conditioner/refiner clean and sanitary.

However, during ship- b. Place the bypass valve(s) in bypass position (See ping, storage, installing and operating, bacteria could get into Figure 6). • SETUP PROCEDURE electronic control compensates automatically after you set the iron level in Step 11, below. When the EcoWater Systems conditioner/refiner is plugged in for the first time, a beep sounds and the dis- 8. Press the SELECT ( ) button.

• S Y S T E M S CONDITIONER/REFINER STATUS SCREENS MAIN MENU During normal operation, the EcoWater Systems condi- tioner/refiner’s display shows up to four status screens (Page 14 explains how individual screens can be turned on or off). Each is shown for six seconds, in a rolling sequence (See Figure 15). • ECOWATER Conditioner/Refiner Operation S Y S T E M S CONNECTING TO REMOTE When the conditioner/refiner’s electronic control is first powered up, it is not yet in communication with the remote.

Do the following to establish a link between FIG. 19 the two: 1.

Instrukciya po ohrane truda dlya hudozhestvennogo rukovoditelya doma kuljturi. • ECOWATER Conditioner/Refiner Operation S Y S T E M S SETTING SALT LEVEL LOW SALT ALARM Use this feature when adding salt to the conditioner/ Use this feature to program when the electronic control refiner. Will display a low salt alarm. The number of days can be customized, or the feature can be turned off. • ECOWATER Conditioner/Refiner Operation S Y S T E M S RECHARGING THE CONDITIONER/REFINER SETTING THE CURRENT TIME When the conditioner/refiner’s electronic control is first This feature may be used to assure an adequate supply of conditioned water at times of unusually high water powered up, a “wizard”. • ECOWATER Conditioner/Refiner Operation S Y S T E M S SETTING RECHARGE TIME SETTING HARDNESS When the conditioner/refiner’s electronic control is first When the conditioner/refiner’s electronic control is first powered up, the default time for starting an automatic powered up, a “wizard” screen prompts you to enter recharge is 2:00 a.m.

• ECOWATER Conditioner/Refiner Operation S Y S T E M S MODIFYING ROLLING SCREENS SETTING THE LANGUAGE During normal conditioner/refiner operation, four status When the conditioner/refiner’s electronic control is first screens are shown in sequence (See “Conditioner/ powered up, a “wizard” screen prompts you to set the Refiner Status Screens”. • ECOWATER Conditioner/Refiner Operation S Y S T E M S SETTING TIME FORMAT SETTING HARDNESS UNITS Use this feature to select a 12-hour (AM/PM) or 24-hour Use this feature to select grains or parts per million clock. (ppm) as hardness units. • ECOWATER Conditioner/Refiner Operation S Y S T E M S SYSTEM INFORMATION Use these features to look up the following information about the conditioner/refiner and its operations: Model information (model number and software version) FIG.